 |
Urban
The qualified raw water is pressurized by the multi-stage pump and then enters the pipeline condenser 2, uses waste heat to heat the raw water, and then enters the preheater 2 and the preheater 1. After heat exchange, it enters the evaporator and is sprayed into the heating tube by the material water distributor. Make material water to flow in a film status on the tube wall, which will be heated and vaporized by industrial steam. The secondary steam with water droplets generated after gasification enters the steam-water separation device from the lower end of the evaporation chamber, and becomes ultra-pure steam after three-stage separation. | | |
1. Structure: The evaporator, preheater and condenser are all designed with double tube sheet, and the inner tube plate is expanded and welded externally to avoid cross contamination. 2. Separation device: three-stage separation with falling film evaporation, gravity separation and spiral flow. 3. Material: all parts in contact with raw water, pure steam, and pure steam condensed are made of SS316L. 4. Thermal preservation and insulation: the evaporator, preheater, and condenser all use aluminum silicate needle punched blanket, which has good extensibility, light weight, excellent heat insulation and strong stability. 5. Surface treatment: The internal and external surfaces are electrochemically polished to effectively ensure the smoothness of the stainless steel surface. The external surface can also be sandblasted. 6. Energy saving and consumption reduction: The evaporator and the separator form a huge communicating device, thus the heat can be fully utilized. The whole equipment can reach its maximum production capacity from standby in a short period of time. The use of liquid level to control the raw water is fully utilized to achieve full energy saving and consumption reduction. The preheater 2 uses industrial steam condensed water for preheating, which saves energy. 7. Stainless steel pipe are used as far as possible to directly stretch the elbow to avoid welding. Welding parts of pipelines and accessories should be automatically welded with argon protection (single-side welding and double-side forming process) to ensure welding quality, and electrochemical polishing after welding. 8. Provide verification materials such as endoscopic inspection photos, solder joint diagrams, pressure test and pickling passivation reports, and system design documents. 9. The control system adopts HMI+PLC fully automatic control, and the operation interface is simple. Various communication modes are available. Control system authority levels: at least three levels of authority can be set. 10. Online monitoring of parameters such as conductivity, temperature and flow. The recorder can choose a paperless recorder or a paper recorder to record and print key parameters. 11. The control system can be equipped with electronic signatures and electronic records to make the system control with audit trail function, and meet the requirements of GAMP 5 and 21 CFR PART 11. | ||
Our Service
Through years of experience, Urban provides several services which cover almost all requirements of clients. These services include production, design, inspection, packaging, shipment, product recommendation, after-sales service, and multiple client solutions.
We can supply mаsk raw materials for you if you can't buy materials from in your local market.
We have a good relationship with more than four international shipping companies who have rich experiences in handling different kinds of shipping ways and also the customs declarations and clearances. They all have good shipping services to save you time and costs.
We have a professional international technical team. To provide you with after-sales service and guidance.
After-sale Service
We will always be responsible for the machine you purchased. Nearly 10 professional after-sales personnel provide global technical services. In this way, we also provide professional services, such as guide installation services, equipment commissioning and operation services, maintenance services and equipment parts replacement. Ensure the quality of your products, while eliminating your worries.
1. The whole machine is guaranteed for 1 years.
2. Provide professional machine operation and maintenance guidelines.
4. Provide 24-hour online professional technical services .
Customer Feedback
The qualified raw water is pressurized by the multi-stage pump and then enters the pipeline condenser 2, uses waste heat to heat the raw water, and then enters the preheater 2 and the preheater 1. After heat exchange, it enters the evaporator and is sprayed into the heating tube by the material water distributor. Make material water to flow in a film status on the tube wall, which will be heated and vaporized by industrial steam. The secondary steam with water droplets generated after gasification enters the steam-water separation device from the lower end of the evaporation chamber, and becomes ultra-pure steam after three-stage separation. |  | |
1. Structure: The evaporator, preheater and condenser are all designed with double tube sheet, and the inner tube plate is expanded and welded externally to avoid cross contamination. 2. Separation device: three-stage separation with falling film evaporation, gravity separation and spiral flow. 3. Material: all parts in contact with raw water, pure steam, and pure steam condensed are made of SS316L. 4. Thermal preservation and insulation: the evaporator, preheater, and condenser all use aluminum silicate needle punched blanket, which has good extensibility, light weight, excellent heat insulation and strong stability. 5. Surface treatment: The internal and external surfaces are electrochemically polished to effectively ensure the smoothness of the stainless steel surface. The external surface can also be sandblasted. 6. Energy saving and consumption reduction: The evaporator and the separator form a huge communicating device, thus the heat can be fully utilized. The whole equipment can reach its maximum production capacity from standby in a short period of time. The use of liquid level to control the raw water is fully utilized to achieve full energy saving and consumption reduction. The preheater 2 uses industrial steam condensed water for preheating, which saves energy. 7. Stainless steel pipe are used as far as possible to directly stretch the elbow to avoid welding. Welding parts of pipelines and accessories should be automatically welded with argon protection (single-side welding and double-side forming process) to ensure welding quality, and electrochemical polishing after welding. 8. Provide verification materials such as endoscopic inspection photos, solder joint diagrams, pressure test and pickling passivation reports, and system design documents. 9. The control system adopts HMI+PLC fully automatic control, and the operation interface is simple. Various communication modes are available. Control system authority levels: at least three levels of authority can be set. 10. Online monitoring of parameters such as conductivity, temperature and flow. The recorder can choose a paperless recorder or a paper recorder to record and print key parameters. 11. The control system can be equipped with electronic signatures and electronic records to make the system control with audit trail function, and meet the requirements of GAMP 5 and 21 CFR PART 11. | ||
Our Service
Through years of experience, Urban provides several services which cover almost all requirements of clients. These services include production, design, inspection, packaging, shipment, product recommendation, after-sales service, and multiple client solutions.
We can supply mаsk raw materials for you if you can't buy materials from in your local market.
We have a good relationship with more than four international shipping companies who have rich experiences in handling different kinds of shipping ways and also the customs declarations and clearances. They all have good shipping services to save you time and costs.
We have a professional international technical team. To provide you with after-sales service and guidance.
After-sale Service
We will always be responsible for the machine you purchased. Nearly 10 professional after-sales personnel provide global technical services. In this way, we also provide professional services, such as guide installation services, equipment commissioning and operation services, maintenance services and equipment parts replacement. Ensure the quality of your products, while eliminating your worries.
1. The whole machine is guaranteed for 1 years.
2. Provide professional machine operation and maintenance guidelines.
4. Provide 24-hour online professional technical services .
Customer Feedback
